Power point installation in Traralgon

A new power point in Traralgon is a short job for a licensed electrician when there is cable access and room on the switchboard, and the Melbourne guide range is $160 to $315 per point. Brick walls, long cable runs and points that need a new circuit cost more than a single double outlet on a plasterboard wall. If your house relies on power boards and extension leads, adding outlets where you actually use them is usually the fix.

Independent licensed electricians receive enquiries sent through this site, then quote and install the points themselves.

Why add power points instead of using power boards?

Many older homes were wired when a room needed one or two outlets: a lamp, a radio, maybe a heater. A modern lounge or bedroom has a television, chargers, a computer, a heater in winter and a fan in summer. The result is double adaptors, power boards plugged into power boards, and leads running under rugs or across doorways.

Signs a room needs more outlets:

• Power boards are permanently daisy-chained or plugged into each other.
• Extension leads run under carpet, through doorways or out a window to the yard.
• A heater, kettle or microwave has to share a power board with other things.
• Outlets are behind heavy furniture and cannot be reached safely.
• A plug feels loose in the socket, or an outlet is cracked or discoloured.

A cracked or scorched outlet should be replaced whether or not you add more. Leads under rugs are a trip and heat hazard, and a power board is not designed to run a heater all evening.

What kinds of outlets can be installed?

Type	Typical use	Notes
Double power point	General use in any room	The standard choice for a new outlet
Power point with USB ports	Bedside, kitchen bench, study	Saves plug-in chargers; check the USB output suits your devices
Relocated power point	Moving an outlet for new furniture or a renovation	The old position is blanked or removed
Dedicated appliance circuit	Oven, cooktop, dryer, air conditioner, spa	Its own breaker and cable from the switchboard
Weatherproof outdoor point	Patio, carport, garden, shed	Lidded weatherproof fitting, sited away from water spray
Isolating switch	Air conditioner, hot water or pump	Lets the appliance be turned off at the unit for service

For the lighting side of a renovation, see the lighting and ceiling fans page. Lights and points are often done on the same visit.

When does an appliance need its own circuit?

High-load appliances draw enough current that sharing a circuit with other outlets can trip breakers or overheat cable. Electricians normally put these on a dedicated circuit:

• Wall ovens and electric cooktops, including induction.
• Clothes dryers in a laundry with a washing machine.
• Split system air conditioners, especially larger units.
• Spa heaters, pool pumps and some workshop tools.

A dedicated circuit needs a free position on the switchboard. If the board is full, still has fuses or has no safety switches, the electrician may say it needs work before anything is added. The switchboard upgrades page explains what that involves. Anyone planning to replace a gas cooktop or heater with electric should ask for the circuit sizing at the same time as the outlet.

What about outdoor power points?

Outdoor points need a weatherproof outlet with a cover, mounted where hoses, sprinklers and rain will not reach the face. They should be on a circuit protected by a safety switch. Energy Safe Victoria notes that safety switches are now compulsory on new residential installations, and a careful electrician will not add an outdoor point to an unprotected circuit. For a shed or carport away from the house, the cable may need to run underground in conduit at a set depth, which adds digging time.

On a bigger block, outdoor points may be wanted for a tank pump, a chook shed light or a workshop. If you are in Glengarry or another town with larger lots, mention how far the shed is from the house so the cable run can be priced.

When you know where the outlets need to go, you can send a power point enquiry with a quick sketch or photos of each wall.

How is a power point installed?

1. The electrician checks the switchboard for spare capacity and which circuit the new point will join.
2. They find a cable route through the ceiling or subfloor to the wall cavity.
3. A hole is cut in the wall lining and the mounting bracket fitted; brick or block walls need chasing.
4. Cable is run and terminated, the outlet is fitted and the circuit is tested.
5. Any wall damage from chasing is left ready for patching, unless patching is in the quote.

With a clear cavity and capacity on the board, the Melbourne price guide describes a new point as a quick job. Brick walls take longer because the cable has to be chased into the masonry, and runs to an upper floor or a far corner of the house take more time in the ceiling.

How much does a new power point cost?

Item	Melbourne guide range
New power point, per point	$160 to $315
Call-out or service fee, per visit	$52 to $160 per visit

These are October 2026 Melbourne metro guide figures, not Traralgon quotes, and a local electrician may price differently for travel and access. Several points on one visit share one call-out, so it pays to list every outlet you want in one go. Dedicated circuits are quoted separately because they include a breaker and a longer cable run back to the board. The electrical cost guide for Traralgon shows the other price bands on this site.

Is it worth adding points during a renovation?

Yes, if the walls or ceilings are going to be open anyway. Cable can be run straight into an exposed stud wall in minutes, where the same point added later to a finished wall means cutting, fishing cable and patching. Before the plasterer arrives, walk each room with a tape measure and mark where beds, desks, the television and bench appliances will sit, then add a point or two more than you think you need. Kitchens and home offices are the rooms people most often wish they had wired more generously.

What paperwork should you get?

New power points and circuits are non-prescribed electrical work in Victoria. That means no independent inspection is required, the work can be turned on when finished, and the electrician must give you a Certificate of Electrical Safety within 30 days, according to Energy Safe’s certificate information for consumers. If the job needed the switchboard changed, that part is prescribed work and must be inspected before it is energised.

What will a careful electrician refuse to do?

• Add a point to a circuit that is already overloaded, or to one with no safety switch protection when outdoors.
• Run cable along the outside of a wall without suitable conduit or mechanical protection.
• Fit a standard indoor outlet in a wet or exposed position.
• Join new cable onto old rubber insulated wiring. If they find it, expect advice about a wider check.

Next step: what to include in a power point enquiry

List each new point and where it goes, for example two doubles beside the bed and one USB double at the kitchen bench. Say whether each wall is plasterboard, brick or something else, and whether the room is upstairs. Note what will plug in, especially heaters, ovens, dryers or air conditioners, and include a switchboard photo if a new circuit may be needed. Put that in an enquiry for new power points with your suburb.

Send a job enquiry